OVERCOME SLOW COMPUTER

OVERCOME SLOW COMPUTER

04:22 Restu

Many Things to Look for in which PC Troubleshooting Slow Complaints are most often found in the office is quite boring for the IT Technical Support? the response to this problem such as "My computer is slow" so about a sentence that is often asked by end users who use a computer, and we have to fix it, it's a very tedious thing to be taken sangking often, sometimes we say "upgrade aja" although we know that's not the right answer is. Because the end user does not know what the execution of. We automatically have to find the cause, sometimes we stressnya so we immediately took steps to re-install it, rather than be bothered to search him permasalahanya, and it would take more time. 

Here are 11 things we should look to address the "My computer is slow!" A. Spyware and Viruses are the most a top to analyze a slow pc is part of this, because it is the easiest part in the infiltrated and many users are interacting to him or her (indirectly), spyware comes from the banners and ads on a web page which went into effect when we access the page / banner through a browser that has security holes that are not good, so that spyware is very close to the IE, because IE is a good friend to spyware, because spyware can allow spyware to install the program on the HDD we are silent, the first step, use firefox! outlines the basic steps to remove spyware: 

1. Identification and analysis process is running with the windows task manager 

2. Identify and disable service in question through the management console 

3. Identify and disable service at startup item in system configuration utilty 

4. Find and delete the existing entry in the registry at startup 

5. Identify and delete suspicious files 

6. Install and use a spyware detection and removal. 

Most modern processors Processor Overheating easy to generate heat, thus cooling the processor of the present requires a special and particular kind of fan, so when tempratur processors increases beyond the limit, the system will slow down and the process will be slow, modern motherboards can monitor and manage tempratur processor, which can done through the bios. 

The processor fan that failed due to: 

1. Dust which hamper the smooth rotation of the fan 

2. Fan motor is damaged 

3. Bearing fan so there is a doll fan "jiggling" 

Jiggling in question here is if the fan is spinning round there was a crick crick quickly it can be said that the fan has started doll bearing fan also does not have to be replaced, if dusty, we only need to clean the dust. 

4. Some bad ram as well as the influence of the situation can be bad ram, this is due to: 

1. RAM timing is slower than optimal machine specifications 

2. RAM has minor value can only be seen after a few test 

3. RAM is too hot 

At this time a lot of RAM fariasi that we can use and we buy, and we can adjust the capacity and capability of our motherboard and do not forget to set the speed of RAM in the bios other bad thing is the RAM chips each its not everything can be stabilized so that it will degrade performance, so that the characteristic feature of the RAM chips are not good is always slow and eventually pc blue screen, if we find that overheated RAM we can use a heatspreader to overcome them (my suggestion, rather than purchasing RAM heatspreader mending buy better RAM only). 

4. If the hard drive hard drive fail often experience failure, it also will worsen the performance of the computer, and type of this kind fail many causes, can be a mechanical, electronic, and even his guns firmware update, from the hard disk will cause: 

1. Access time slow 

2. The number of bad sectors that continue to increase when the scandisk or chkdsk 

3. There are guns unexplained bluescreen 

4. Boot failed to detect the hard drive was still in good condition or guns it easy easy difficult, usually most frequent in windows xp slalu appears "Windows delayed write failure" when hard drive failure, well that's when we begin to anticipate what on earth on the hard drive, first we can do a scan with chkdsk, until we examine the physical hard drive. physical hard drive usually can be seen from the noise, the noise means signify components in which there is a loose start, we can also shake shake to the left and right hard drive and listen to the sound, if you want to use the tools and periodically check the condition of the hard drive we can use the tools hddlife, there is a free no pay. 

5. Bios Settings Normally bios that have not been in his custom setting will mengamlami slowing the process a few seconds, especially at boot time, for that we must mengcustom bios settings so that job performance boot process can be accelerated, in general bios settings to be considered are: 

1. Boot directly to hard disk 

2. Disable unused IDE drive 

3. Set speed RAM latency 

4. Turn off the IO / IRQ unused onboard devices 

5. Use Fast POST 

6. Disk type / controller compatibility spele It is sometimes, but this will be felt when we use an application that will deplete the disk performance, usually motherboards now have a good controller for the parallel ATA disk, but we must pay attention to its IDE cable, because cable has a particular specification, there is a UDMA 33, 66, and 100, if we look physically, the shape of the cord has smooth fibers and a lot smoother, while the UDMA 33 fibers slightly, so use a cable that has a high specification for the disk. and do not forget, every 18 months it would appear the disk with the latest technology and capacity so do not forget to plan for making such changes will give a good effect for us. Also if the motherboard in use today is the motherboard that is equipped with SATA Disk controler it will be even better, because sata faster than pata 7. Services By default Windows service that runs on all windows, even though directly we do not know if we need it or not, the service can be accessed from the control panel, administrative tools and services, many service service is not required to be stopped, so we can save the unused RAM in the computer and the computer can automatically run better, some services that must be turned off if we do not need it is: 

1. FTP 

2. Indexing Service 

3. Remote Registry 

4. Telnet 

5. Remote Access 

6. Remote Desktop 

7. Automatic Update 

8. Sometimes the process is invisible, we know there without any programs running in memory, even though we do not use it again or we even have menguninstallnya but the program still running, for that we should pay attention to process what is happening in our computer with a view task manager, and we can end task it or kill, then we can delete it. its exe 

9. Disk Fragmentation As the characteristics of a file in a computer must have the file on add, edit, or delete it, it can lead to fragmentation in some areas of the hard disk sectors, for that we need data on the computer after finish us, ie to defragment it. if we use windows xp, we can use the Defrag.exe and meletakanya on schedule to run at the time that we set 

10. Background applications If we look at the systray when we click the left arrow icon will berderetlah a lot, more and more attached to the systray icon that causes the computer to respond to the slower process, because a lot of unused memory to process it, so for that we need mematikanya or disable switch is not required to access the registry: 

HKEY_ LOCAL_MACHINE \ Software \ Microso ft \ Windows \ CurrentVe rsion \ Run and HKEY_LOCAL_MACHINE \ Software \ Mi crosoft \ Windows \ CurrentVersion \ RunOnce Delete the key is not required. 

11. File system issues Some issues affecting the performance of file system it may be true, if we use the OS Windows NT 4.0, Windows 2000, or Windows XP, you should use the NTFS file system because NTFS has better performance than the previous example, the FAT32 filesystem, which fat32 This from the performance he was only able to handle a capacity of 32GB disk with the default cluster size, if it runs fat32 filesystem on the disk is large it will often occur pc fragmentation and declining performance. Format and size of the cluster also has an effect, for example, we have a 60GB disk and then format the disk with a cluster size of 512 bytes, this will cause the disk where the cluster will use a lot of the hard drive will often do the track and seeknya, and this will be problematic when the hard drive when the disc has a lot framgentasi, one solution is to use a larger cluster, such as 4K or larger, from there we will see improvement notice on load times, and please note, the larger the cluster size will significantly increase the amount of cluster slack space and many, many make a lot of wasted disk space.